Mobiliojo krano teleskopinis cilindras

The mobile crane telescopic cylinder is vital in mobile crane systems and is specifically designed to enhance reach and lifting performance. This hydraulic cylinder enables crane operators to extend the boom sections of the crane, allowing for increased vertical and horizontal reach and improved lifting capacity.

The mobile crane telescopic cylinder is a crucial component that enhances mobile cranes’ reach, lifting capacity, and overall performance. With its robust construction, telescopic design, extended reach, and improved lifting capacity, this hydraulic cylinder empowers operators to tackle diverse lifting tasks easily and efficiently. By following the recommended usage methods and maintenance practices, operators can maximize the longevity and performance of the mobile crane telescopic cylinder, contributing to increased productivity, versatility, and safety on construction sites and industrial applications. Invest in this essential hydraulic component to elevate the capabilities of your mobile crane, ensuring successful and efficient lifting operations.

Mobile Crane Telescopic Cylinder Key Characteristics:

1. Tvirta konstrukcija:

• The mobile crane telescopic cylinder is engineered with high-quality materials, ensuring durability and longevity even in demanding operating conditions.
• It is designed to withstand heavy loads, vibrations, and extreme weather conditions, providing reliable performance throughout its lifespan.

2. Telescopic Design:

• This hydraulic cylinder features a telescoping mechanism that allows for the extension and retraction of multiple boom sections.
• The telescopic design enables the crane to reach greater heights and distances, making it suitable for a wide range of lifting tasks.

3. Enhanced Reach and Flexibility:

• By extending the boom sections, the telescopic cylinder significantly increases the crane’s reach, both vertically and horizontally.
• It enables operators to access elevated work areas, maneuver around obstacles, and reach over obstacles, enhancing the crane’s versatility on the job site.

4. Improved Lifting Capacity:

• The telescopic cylinder enhances the crane’s lifting capacity by providing greater stability and reducing the stress on individual boom sections.
• It distributes the load more evenly across the extended boom, allowing for safer and more efficient lifting operations.

Mobile Crane Telescopic Cylinder Parameter:

Mobiliojo krano identifikavimo schema:

Usage Method Of Mobile Crane Telescopic Cylinder:

1. Saugos priemonės:

• Prieš pradėdami dirbti su mobiliuoju kranu, įsitikinkite, kad laikomasi visų saugos nurodymų ir taisyklių.
• Conduct a thorough inspection of the crane and its components, including the telescopic cylinder, to ensure they are in proper working condition.

2. Susipažinkite su valdikliais:

• Supraskite savo mobiliojo krano modeliui būdingus valdymo mechanizmus ir veikimo procedūras.
• Identify the controls responsible for extending and retracting the telescopic boom sections.

3. Extending the Boom:

• Activate the appropriate control to extend the telescopic cylinder, allowing the boom sections to develop fully.
• Follow the manufacturer’s guidelines and load charts to determine the safe extension limits based on the load weight and radius.

4. Retracting the Boom:

• When the lifting operation is complete, activate the control to retract the telescopic cylinder, bringing the boom sections back to their resting position.
• Ensure that each section retracts smoothly and aligns properly with the adjacent areas.

How To Bleed Air From A Hydraulic System?

Bleeding air from a hydraulic system is necessary to ensure proper operation and prevent issues such as reduced performance, spongy response, or erratic behavior. Here’s a step-by-step guide on how to bleed air from a hydraulic system:

1. Nustatykite kraujavimo taškus:
   • Determine the locations in the hydraulic system where air can be trapped. Common bleed points include air bleed valves, bleed screws, or fittings with removable caps.
   • Consult the system’s manual or manufacturer guidelines for specific information on bleed points.
2. Paruoškite sistemą:
   • Ensure the hydraulic system is turned off and the pressure is fully released.
   • If applicable, locate the hydraulic fluid reservoir and check the fluid level. Maintain the liquid level within the recommended range.
3. Start at the Lowest Point:
   • Begin the bleeding process at the lowest point in the system where air can accumulate.
   • Loosen the air bleed valve or remove the fitting cap to expose the bleed screw.
4. Open the Bleed Point:
   • Use an appropriate tool, such as a wrench or screwdriver, to slowly open the air bleed valve or loosen the bleed screw.
   • Be cautious not to remove the valve or screw, which may result in fluid leakage.
5. Purge the Air:
   • As the bleed point is opened, air bubbles may start to escape along with hydraulic fluid.
   • Allow the air to purge from the system until a steady fluid flow without air bubbles is observed.
   • Keep a container or absorbent material handy to catch any fluid that may spill during this process.
6. Close the Bleed Point:
   • Once the air is purged, close the air bleed valve or tighten the bleed screw securely.
   • Ensure the valve or screw is adequately sealed to prevent further air entry.
7. Move to the Next Bleed Point:
   • Proceed to the next highest point in the system where air can accumulate, and repeat steps 4-6.
   • Continue bleeding the system at each identified bleed point, working your way up to the highest point.
8. Patikrinkite skysčio lygį:
   • Monitor the fluid level in the reservoir throughout the bleeding process and top up if necessary.
   • Use the recommended hydraulic fluid specified in the system’s manual or by the manufacturer.
9. Patikrinkite ir patikrinkite:
   • After bleeding all the identified points, operate the hydraulic system to ensure proper functionality.
   • Check for any signs of spongy response, abnormal noises, or erratic behavior.
   • Repeat the bleeding process if issues persist or consult a qualified technician for further assistance.

Gamyklos pajėgumai ir talpa:

(1) Surinkimas

Turime pirmos klasės nepriklausomą tyrimų ir plėtros surinkimo platformą. Hidraulinių cilindrų gamybos ceche yra keturios pusiau automatinės kėlimo cilindrų surinkimo linijos ir viena automatinė pakreipimo cilindrų surinkimo linija, kurių projektinis metinis gamybos pajėgumas yra 1 milijonas vienetų. Specialiųjų cilindrų ceche įrengta įvairių specifikacijų pusiau automatinė valymo surinkimo sistema, kurios projektinis metinis gamybos pajėgumas yra 200 000 vienetų, ir garsi CNC apdirbimo įranga, apdirbimo centras, didelio tikslumo cilindrų apdirbimo speciali įranga, robotinis suvirinimo aparatas, automatinis valymo aparatas, automatinis cilindrų surinkimo aparatas ir automatinė dažymo gamybos linija. Esama daugiau nei 300 rinkinių (komplektų) kritinė įranga. Optimalus įrangos išteklių paskirstymas ir efektyvus naudojimas užtikrina gaminių tikslumo reikalavimus ir aukštus gaminių kokybės poreikius.

(2) Apdirbimas

Mechaninio apdirbimo ceche įrengtas pritaikytas nuožulnaus bėgio tekinimo centras, apdirbimo centras, greitaeigis galandimo staklės, suvirinimo robotas ir kita susijusi įranga, galinti apdirbti cilindrinius vamzdžius, kurių maksimalus vidinis skersmuo yra 400 mm, o maksimalus ilgis – 6 metrai.

(3) Suvirinimas

(4) Dažymas ir dengimas

Su mažomis ir vidutinio dydžio cilindrinėmis automatinėmis vandens pagrindo dažų dengimo linijomis, siekiant automatinio robotų pakrovimo ir iškrovimo bei automatinio purškimo, projektinis pajėgumas yra 4000 vienetų per pamainą;
Taip pat turime pusiau automatinę didelių cilindrų dažų gamybos liniją, varomą grandinės, kurios projektinis našumas yra 60 dėžių per pamainą.

(5) Testavimas

Turime aukščiausios klasės patikros patalpas ir bandymų stendus, kad užtikrintume, jog baliono veikimas atitinka reikalavimus.

Esame vienas geriausių hidraulinių cilindrų gamintojų. Galime pasiūlyti išsamius hidraulinius cilindrus. Taip pat teikiame atitinkamus žemės ūkio pavarų dėžėsMes eksportuojame savo gaminius klientams visame pasaulyje ir pelnėme gerą reputaciją dėl aukščiausios gaminių kokybės ir aptarnavimo po pardavimo. Mes laukiame klientų šalyje ir užsienyje, norinčių susisiekti su mumis derėtis dėl verslo, keistis informacija ir... bendradarbiauti su mumis!