Hydraulic System For Mine

Hydraulic systems for mine are a specialized solution designed to meet the unique challenges faced in mining operations. This advanced hydraulic system improves underground and open pit mines’ safety, productivity, and efficiency. With its robust construction, high-performance components, and intelligent control functions, mine hydraulic systems are tailored to meet the demanding requirements of the mining industry.

Hydraulic System For Mine Parameter:

Motor Power:2.2KW
Oil Tank:80L
System Flow:59L/min

Opis modela hidravličnega sistema po meri:

Struktura rezervoarja za olje:

Pokrovček za čiščenje rezervoarja za olje:

Hidravlični sistem po meri:

(1) Vertikalni hidravlični sistem

(2) Horizontalni hidravlični sistem

(3) Hidravlični sistem za bočno montažo

Stranska hidravlična črpalna postaja, torej naprava za oljno črpalko, je nameščena vodoravno na podlagi ločenega rezervoarja, stranski tip pa je lahko opremljen z rezervno črpalko, ki se uporablja predvsem za sistem z veliko prostornino poštnega predala 250 litrov in električno močjo 7,5 kW ali več.

Hydraulic System for Mines Značilnosti:

1. Heavy-Duty Components:
   • The system integrates rugged hydraulic components, including pumps, valves, and cylinders, to withstand the harsh conditions of mining operations.
   • These components are designed with high load capacity, extended service life, and resistance to wear, corrosion, and extreme temperatures.
2. Funkcije inteligentnega upravljanja:
   • Mine hydraulic system usually integrates advanced control technology, such as a programmable logic controller (plc) and complex hydraulic control system.
   • These intelligent features enable precise and automatic control of hydraulic functions, ensuring optimal performance and adaptation to different mining tasks.
3. Fluid Contamination Control:
   • Mining environments are prone to high dust, dirt, and other contaminants that can impact the hydraulic system’s performance.
   • The Hydraulic System for Mines incorporates effective filtration and contamination control measures, such as high-quality filters and reservoir breathers, to maintain clean hydraulic fluid and protect system components.

Kako odstraniti zrak iz hidravličnega sistema?

To remove air from a hydraulic system, commonly referred to as “bleeding” the system, follow these step-by-step instructions:

1. Priprava:
   • Ensure the hydraulic system is powered off and depressurized. This step is crucial for safety and prevents accidental movement or fluid discharge during the bleeding process.
   • Put on appropriate personal protective equipment (PPE), such as safety glasses and gloves, to protect yourself from potential fluid spray.
2. Locate Bleeder Valves:
   • Identify the bleeder valves in the hydraulic system. These valves are typically located on or near hydraulic cylinders, actuators, or components prone to air entrapment.
   • Consult the system’s documentation or manufacturer’s guidelines to locate specific bleeder valves for your system.
3. Pozicioniranje:
   • Position a suitable catch container or absorbent material beneath the bleeder valve to collect any fluid that may be discharged during the bleeding process.
4. Opening the Bleeder Valve:
   • Using an appropriate wrench or tool, slowly and partially open the bleeder valve. Take care not to fully remove the valve at this stage.
   • Opening the valve allows trapped air to escape while allowing hydraulic fluid to flow out in a controlled manner.
5. Purging Air from the System:
   • Activate the hydraulic system, typically by operating the associated machinery or actuating the components connected to the bleeder valve.
   • As the system operates, the hydraulic fluid flow will push air bubbles towards the open bleeder valve, helping to purge the air from the system.
   • Allow the system to cycle several times to ensure thorough purging of the air from the hydraulic system.
6. Fluid Discharge:
   • Monitor the fluid discharging from the bleeder valve. Initially, you may observe air bubbles, followed by a steady flow of hydraulic fluid without air.
   • Continue the bleeding process until all air bubbles are eliminated, and only a consistent flow of fluid is discharged from the valve.
7. Closing the Bleeder Valve:
   • Once air is completely purged from the system, carefully close the bleeder valve using the appropriate wrench or tool.
   • Ensure the valve is tightened securely to prevent any fluid leakage.
8. System Verification:
   • Verify the hydraulic system’s operation to ensure it functions properly without any abnormal noises, vibrations, or performance issues.
   • Monitor the system for any signs of air re-entry, such as spongy or inconsistent actuation, and repeat the bleeding process if necessary.

Zmogljivost in zmogljivost tovarne:

(1) Sestavljanje

Imamo prvovrstno neodvisno platformo za raziskave in razvoj. Delavnica za proizvodnjo hidravličnih cilindrov ima štiri polavtomatske montažne linije za dvižne cilindre in eno avtomatsko montažno linijo za nagibne cilindre z letno proizvodno zmogljivostjo 1 milijona kosov. Delavnica za posebne cilindre je opremljena z različnimi specifikacijami polavtomatskega sistema za čiščenje in montažo z letno proizvodno zmogljivostjo 200.000 kosov ter znano CNC obdelovalno opremo, obdelovalnim centrom, visoko precizno posebno opremo za obdelavo cilindrov, robotskim varilnim strojem, avtomatskim čistilnim strojem, avtomatskim strojem za montažo cilindrov in avtomatsko proizvodno linijo za barvanje. Obstoječa kritična oprema obsega več kot 300 kompletov (kompletov). Optimalna razporeditev in učinkovita uporaba opremnih virov zagotavljata zahteve glede natančnosti izdelkov in izpolnjujeta visoke zahteve glede kakovosti izdelkov.

(2) Strojna obdelava

Strojna delavnica je opremljena s prilagojenim centrom za struženje nagnjenih tirnic, obdelovalnim centrom, visokohitrostnim strojem za honanje, varilnim robotom in drugo sorodno opremo, ki lahko obdeluje cilindrične cevi z največjim notranjim premerom 400 mm in največjo dolžino 6 metrov.

(3) Varjenje

(4) Barvanje in premazovanje

Z majhnimi in srednje velikimi cilindričnimi avtomatskimi linijami za barvanje na vodni osnovi, za doseganje avtomatskega nakladanja in razkladanja robotov ter avtomatskega brizganja, je projektna zmogljivost 4000 kosov na izmeno;
Imamo tudi polavtomatsko linijo za proizvodnjo barv za velike jeklenke, ki jo poganja veriga, s projektno zmogljivostjo 60 zabojev na izmeno.

(5) Testiranje

Imamo prvovrstne inšpekcijske prostore in testne postaje, s katerimi zagotavljamo, da delovanje jeklenke izpolnjuje zahteve.

Smo eden najboljših proizvajalcev hidravličnih sistemov. Ponujamo vam celovit hidravlični sistem. Zagotavljamo tudi ustrezne kmetijski menjalnikiNaše izdelke smo izvozili strankam po vsem svetu in si prislužili dober ugled zaradi vrhunske kakovosti izdelkov in poprodajnih storitev. Z veseljem vas vabimo, da nas kontaktirate za poslovne dogovore, izmenjavo informacij in ... sodelujte z nami!